HERMS Coil Kettle Adapter Tri-Clamp 1.5" x 1/2" Female
HERMS Coil Kettle Adapter Tri-Clamp 1.5" x 1/2" Female
- Delivery time: 2-5 Workdays
In stock
Couldn't load pickup availability
SKU:
SKU:TFK19625
![HERMS Spirale Tri-Clamp Kesseladapter 1/2" BSP-1](http://www.crafthardware.de/cdn/shop/products/HERMS-Coil-Tri-Clamp-Kettle-Mount-1-2-BSP-1_02b7df7b-16ae-4f93-a73c-67aee3b76b32.jpg?v=1664626355&width=1445)
![HERMS Spirale Tri-Clamp Kesseladapter 1/2" BSP-2](http://www.crafthardware.de/cdn/shop/products/HERMS-Coil-Tri-Clamp-Kettle-Mount-1-2-BSP-2_dc1159d8-f919-4ceb-a9cc-90b5105e481c.jpg?v=1664626356&width=1445)
![HERMS Spirale Tri-Clamp Kesseladapter 1/2" BSP-4](http://www.crafthardware.de/cdn/shop/products/HERMS-Coil-Tri-Clamp-Kettle-Mount-1-2-BSP-4_d465282b-f0ea-457a-83e9-e6babb36742c.jpg?v=1664626356&width=1445)
![HERMS Spirale Tri-Clamp Kesseladapter 1/2" BSP-3](http://www.crafthardware.de/cdn/shop/products/HERMS-Coil-Tri-Clamp-Kettle-Mount-1-2-BSP-3_3909d33c-2647-4d32-9853-775859b151dd.jpg?v=1664626356&width=1445)
![HERMS Spirale Tri-Clamp Kesseladapter 1/2" BSP-5](http://www.crafthardware.de/cdn/shop/products/HERMS-Coil-Tri-Clamp-Kettle-Mount-1-2-BSP-5_2d86928d-b078-4633-93ee-6cc47ba3f196.jpg?v=1664626356&width=1445)
Product Description
This BSP adapter is used to install our HERMS coil in a Craft Hardware flat-bottomed HERMS HLT kettle or other converted Tri-Clamp kettle. The coil is installed through two Tri-Clamp ports on your kettle, and you will need two of these to install your coil. Outside the kettle you can attach any standard 1.5" Tri-Clamp fitting. Completely remove your HERMS spiral from your kettle for cleaning, super fast and super easy. No tools or teflon tape required.
This fitting requires a DN40 Tri-Clamp ferrule on your kettle. It will not work with the slightly smaller 1.5" ferrules found commonly in threaded conversion kits.
If you have a permanently installed HERMS coil that is screwed into your kettle with the 1/2" lockrings, you need a different adapter found here.
Specifications:
- Tri-Clamp size 1.5" (2x)
- Inner diameter: 11 mm
- Thread: 1/2" BSPP female
- Gasket: EPDM
The fitting includes a robust EPDM gasket specially sized for this application. It is more tear resistant than silicone and seals without compressing into the fluid path. No Teflon tape is necessary. Lightly hand-tighten the fitting, do not over tighten!
Note: This product is intended for use only with the BrewPi coils which are also sold here in our shop. It requires a sufficiently wide flat surface on the coil fitting to make a proper seal. May not work with other 1/2" threaded HERMS coils.
Installation:
- Place the HERMS coil ends through the Tri-Clamp ports in your HERMS kettle
- Screw on the Tri-Clamp adapter from the outside with the EPDM gasket in place. Lightly hand-tighten only!
- Install the Tri-Clamp clamp between the adapter and the kettle with a normal Tri-Clamp gasket.